TECHNICAL DATA SRT-01
STOPS RUST
ENAMEL SPRAYS
Form: CS2201
Rev.: 090313
.DESCRIPTION AND USES .
Rust-Oleum
®
Stops Rust
®
Enamel Sprays are designed to
provide a durable protective coating with excellent rust
prevention, and excellent resistance to abrasion, fading, chipping,
and dulling. These sprays apply easily, provide excellent
coverage and dry fast to a tough attractive finish. Rust-Oleum
®
Stops Rust
®
Enamel Sprays are ideal for ferrous, non-ferrous
metal and wood surfaces. It features a comfort tip with a wider
finger pad to reduce fatigue caused by continuous spraying and
an any-angle tip which allows you to spray at any angle. Not for
use on galvanized metal.
.PRODUCTS .
SKU Description SKU Description
7701830 Crystal Clear 7792830 Gloss White
7721830 Fresh Blue 7794830 Antique White
7722830 Harbor Blue 7797830 Semi-Gloss White
7723830 Navy 7798830 Semi-Gloss Black
7724830 Sail Blue 214084 Orange
7727830 Royal Blue 214085 Flat Brown
7731830 Grass Green 214086 Charleston Green
7733830 Dark Hunter Green 214087 Army Green
7738830 Hunter Green 241235 Pistachio
7747830 Sunburst Yellow 241236 Glacier Blue
7754830 Anodized Bronze 245897 Burnt Orange
7762830 Sunrise Red 248567 Merlot
7763830 Carnival Red 248568 Cherry
7765830 Regal Red 248569 Emerald
7768830 Burgundy 248630 French Roast
7770830 Almond 248631 Night Tide
7771830 Sand 249032 Khaki
7775830 Leather Brown 250702 Pure White
7776830 Flat Black 250703 Cobblestone
7779830 Gloss Black 250704 Lobster Red
7783830 Pewter Gray 250705 Fern
7784830 Charcoal Gray 262661 Dark Walnut
7786830 Smoke Gray 267112 Kona Brown
7789830 Canvas White 269292 Maui Blue
7790830 Flat White
.PAINTING CONDITIONS .
Use outdoors or in a well ventilated area such as an open
garage. Apply when temperature is between 50-90°F (10-
32°C) and humidity is below 65% to ensure proper drying.
Do not apply to surfaces, when heated, exceed 200°F
(93°C). Do not apply to galvanized steel. Avoid spraying in
very windy and dusty conditions. Cover surrounding area
to protect from spray mist.
..PRODUCT APPLICATION .
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical
contaminants by washing the surface with a commercial
detergent, or other suitable cleaning method. Rinse with
fresh water and allow to thoroughly dry. Remove loose
paint and rust with a wire brush or sandpaper. Previously
coated surfaces must be sound and in good condition.
Smooth, hard, or glossy finishes should be scarified by
sanding to create a surface profile. . WARNING! If you
scrape, sand or remove old paint from any surface, you
may release lead paint dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO
AVOID EXPOSURE. Wear a NIOSH approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
PRIMING
Use of a Rust-Oleum
®
primer provides added corrosion
protection, excellent adhesion and hiding and is especially
recommended for bare wood and metal. The following
primers are recommended.
7769 Rusty Metal Primer
7780 Clean Metal Primer
2081 Light Gray Auto Primer
2067 Red Auto Primer
2089 Dark Gray Auto Primer
(2 pages)
(1 pages)
(1 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals